Форум за електроника

[remi]

Телевизора се държи много зле.Има намален размер по вертикала.При търсене на програми намира много малко.Като ги запомни при набиране са много влошени.Съмявам се на променени настройки на нивото на сигнала.Ще съм благодарен и за дъмп за паметта.благодаря предварително.

[dima]

Изпращам Ви паметта.
_________________
Димитър

[EUROFIX]

NEO SERVICE INFO
TV2K - TXT

COLOUR TELEVISION RECEIVER

SERVICE MANUAL




SECIFICATION

? SYSTEM PAL/SECAM,B/G,DK, I.
? POWER INPUT AC 170-245V(50/60Hz)
? POWER CONSUMPTION 60W
? AERIAL IMPEDANCE 75OHM UNVALANCED
? TUNER VOLTAGE SYNTHESIZER TUNING
? RECEIVING CHANNELS VHF-L E2-S6
VHF-H S7-S41
UHF E21-E69
? PROGRAMME MAX.99 PROGRAM MEMORIES
? PICTURE TUBE 14”,20”,21”;90°
? SOUND OUTPUT 2.0W
? SPEAKER 3W 8 OHM
? AV JACKS FULL SCART ?1









CAUTION: Before servicing the chassis, read the “Safely Precaution”.
“X -Ray radiation Precaution” and “Product Safety Notice” in this manual.

X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To
Avoid such hazards the high voltage must be specified limit. The normal value of the high voltage of this receiver is 24.5KV +/-2KV under 230V AC power source. The high voltage must not exceed 27KV.
2. Each time a receiver requires servicing the high voltage should be checked following the HIGH VOLTAGE CHECK procedure in this manual. It is recommended the reading of the high voltage be recorded as a part of the service record. It is important to use an accurate and reliable high voltage meter.
3. The primary source of X -RAY RADIATION in this TV receiver is the picture tube. For continued X-RAY RADIATION protection, the replacement tube must be exactly the same type tube as used in this TV receiver.
4. Some parts in this receiver have special safety-related characteristics for X-RAY RADIATION protection. For continued safety, parts replacement should be undertaken only after referring the PRODUCT SAFETY NOTICE below.

SAFETY PRECAUTION

WARNING: Service should not be attempted by anyone unfamiliar with the necessary
Precautions on this receiver.
The following are the necessary precautions to be observed before servicing this chassis.
1. Since the power supply circuit of this receiver is directly connected to the AC power line. An isolation transformer should be used during any dynamic service to avoid possible shock hazard.
2. Always discharge the picture tube anode to the CRT conductive coating before handling the picture tube. The picture tube is highly evacuated and if broken, glass fragments will be violently expelled. Use shatterproof goggles and keep picture tube away from the unprotected body while handling.
3. When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as: nonmetallic control; knobs, insulating covers, shields, isolation resistor-capacitor, network, etc.
4. When replacing parts or circuit boards, disconnect the power cord.
5. When replacing a high voltage resistor (metal oxide resistor) on circuit hoard, keep the resistor APP. 10mm(1/2 in.) away from circuit board.
6. Connection wires must be kept away from components with high voltage or high temperature.
7. If any fuse in this TV receiver is blown, replace it with the FUSE specified in the chassis parts list.
8. The receiver is designed to operate with 230V(50Hz) AC mains.


PRODUCT SAFERY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics are often passed unnoticed by a visual inspection and the X-RAY RADIATON protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, X-RAY RADIATION or other hazards.


GENERAL ADJUSTMENT

AUTOMATIC DEGAUSSING
An automatic degaussing coil is attached around the picture tube, degaussing the tube properly in about one second after the set is switched on. If the receiver is moved or faced on a different direction, the power must be switched off at least 15 minutes in order that the automatic degaussing circuit operated properly. External degaussing is necessary if the automatic degassing proves ineffective after the set is moved.

B+ ADJUSTMENT

CAUTION: To avoid X-ray hazards and result in a nominal display width, B+ voltage must be set in the scale of 108.0V+/-0.5V.
1. Make sure the AC power supply is 230V, 50Hz.
2. Switch on the TV receiver, tune in an active channel.
3. Measure the voltage between C641 on Main P.C. Board by DC voltmeter.
4. Set contrast, brightness, color to maximum.
5. Adjust VR631 on Main P. C. Board for B+108.0V+/-0.5V voltage reading.

HIGH VOLTAGE CHECK

CAUTION: There is no high voltage adjustment in this chassis, B+108V voltage directly relates to the high voltage. The high voltage does not exceed 27KV under any conditions.
1. Connect an accurate high voltage meter to the second anode cap of the picture tube.
2. Turn on the receiver, set brightness and contrast to minimum (Zero beam current).
3. Make sure the high voltage does not exceed 27KV.
4. NO matter whether the luminance, contrast and chrominance controls are set to maximum or minimum, the high voltage must be kept under 27KV.



FOCUSING

Receive a TV test pattern signal; adjust controls for optimum picture. Adjust Focus Control for a well-defined, sharpest display in the center area of the screen.



ADJUSTMENT AND SERVICING THE CHASSIS
SERVICE MODE

To enter the service mode, a special remote control which contains an additional SERVICE key must be used. See the illustration. Press the ‘SERVICE’ key on remote control, TV will display service menu as following table 1 line by line. To select the parameter by using the ‘P+/P-’ keys. To adjust the selected parameter by using the ‘V+/V-’ keys. To quit the service mode, press the ‘P.P.’ key on remote control when in the service mode.

Table 1
Parameter Value 14 “ Value 20”, 21 “
Red Gain 32 40
DC Red 063 063
Green Gain 32 40
DC Green 063 063
Blue Gain 32 40
DC Blue 063 063
Apr Threshold 12 12
Logo 6------------ 6------------



To enter the table 2, press the ‘OK’ key for the first time on the remote control when in the service mode.

Table 2
Parameter Value
Tuner AGC 22
H position 32
VPOS 50 10
VPOS 60 10
VAMP 50 47
VAMP 60 53
Bright max 63
Bright min 00
Sub Tint 32
VCO Coarse 05
VCO Fine 063
VCO Coarse L1 05
VCO Fine L1 080

To enter the table 3, press the ‘OK’ key for the second time on the remote control when in the service mode.

Table 3
Parameter Value
AGC gain 00
Option 1 48
Option 2 00
Option 3 06
Option 4 09
Option 5 00
ST Ttext 00
H POS OSD 001
V POS OSD 01
H POS TXT 066
V POS TXT 04
Following are the items of the OPTIONS in more details.
OPTION1:
B5=P/N/S Crystals application (0=2 crystals, 1=1 crystal)
B4=Cutoff Loop (0= OFF, 1=ON)
B3=Safety_Reset (0=Active, 1=non)
B2=Super Tuner (0=OFF, 1=ON)
B1=Sound Demodulation (0= Intercarrier/MONO, 1=QSS/NICAM)
B0=Logo Display (0=OFF, 1=ON)
OPTION2: (It’s better to keep the default setting option2=0)
B5=Half_Contrast (0=OFF, 1=ON)
B4=Color 6db (0=OFF, 1=ON)
B3=APR Feature (0=ON, 1=OFF)
B2=Black Stretch (0=ON, 1=OFF)
B1=Auto Flesh (0=ON, 1=OFF)
B0=Coring (0=ON, 1=OFF)
OPTION3:
B5=AVL (0=OFF, 1=ON)
B4=PIF Over modulation (0=OFF, 1=ON)
B3=Market_France-SECAM L/L’ (0=OFF, 1=ON)
B2=Manual/Auto Cutoff (0=Manual, 1=Auto Cutoff)
B1=Mute pin Low/High To control the speaker (0=Low, 1=High)
B0=TDA7449/TDA7439 (0=TDA7449, 1=TDA7439)
OPTION4:
B4=SCART2 (0=OFF, 1=ON)
B3=RGB (0=OFF, 1=ON)
B2=SVHS (0=OFF, 1=ON)
B1=AV2 (0=OFF, 1=ON)
B0=AV1 (0=OFF, 1=ON)
OPTION5 and ST Ttext is for teletext setting only. It normally could not be changed. If it’s necessary to adjust the OPTION 5, please read the following information before adjustment.
A. For CPUs with English, French, German, Polish or English, French, German, Turkish, Please refer to the setting as below.
1. If OPTION 5 = 00, then the TEXT languages like "ENGLISH, FRENCH, SWEDISH, TURKISH, GERMAN, PORTUGUESE, ITALIAN, RUMANIAN " can be decoded.
2. If OPTION 5 = 02, then the TEXT languages like "POLISH, FRENCH, ESTONIAN, CZECH, GERMAN, SERBIAN, LETTISH, RUMANIAN " can be decoded.
3. If OPTION 5 = 04, then the TEXT languages like "ENGLISH, FRENCH, SWEDISH, CZECH, GERMAN, PORTUGUESE, LETTISH, RUMANIAN " can be decoded.
4. If OPTION 5 = 06, then the TEXT languages ENGLISH, FRENCH, SWEDISH, TURKISH, GERMAN, PORTUGUESE, LETTISH, RUMANIAN can be decoded.
B. For coming new OTP/CPU with English, Russian, Czech, Polish, the setting of the OPTION 5 will be changed as below.
1. If OPTION 5 = 00, then the TEXT languages like "ENGLISH, FRENCH, SWEDISH, CZECH, GERMAN, PORTUGUESE, ITALIAN, RUMANIAN " can be decoded.
2. If OPTION 5 = 02, then the TEXT languages like "ENGLISH, RUSSIAN, SWEDISH, TURKISH, GERMAN, PORTUGUESE, ITALIAN, RUMANIAN " can be decoded.
3. If OPTION 5 = 04, then the TEXT languages like "POLISH, RUSSIAN, SWEDISH, CZECH, GERMAN, SERBIAN, ITALIAN, RUMANIAN " can be decoded.
4. If OPTION 5 = 06, then the TEXT languages like "POLISH, RUSSIAN, SWEDISH, CZECH, GERMAN, PORTUGUESE, ITALIAN, RUMANIAN can be decoded.
Normally, it is supposed not to set OPTION 5 = 01. If you set the OPTION 5 = 01, then the font can be switched by press key MENU on remote control in TEXT mode for TV3K. If you set OPTION 5 = 00, 02, 04, 06, then there is no any activity while press MENU in TEXT mode. Please check.

A.F.C. ADJUSTMENT
Removing any R.F. signal source and prevent any stray signal source from entering the tuner by shorting the tuner input inner contact to the out screen.
Inject the 38.9 MHZ carrier into the tuner IF output pin (pin 11).Select the parameter ‘VCO Coarse’ in the service mode (see Table 2).The ‘VCO Status…’will appear on the screen. Then press the ‘AV’ key on remote control, the CPU will adjust automatically until the ‘VCO Status OK’ appears on the screen. If this can not be achieved, i.e. there is no any pattern on the screen, please adjust the T201 first until a stable pattern appears on the screen. And then press the ‘AV’ key on remote control. The CPU will adjust automatically once again until the ‘VCO Status OK’ appears on the screen.

GEOMETRY
To adjust the picture position and vertical size, select the appropriate parameter in the service mode and adjust as necessary. Please see table 2.

Remote control
29 DIRECTIVTY 6m(MIN) 8m(NOR) OK
30 DIRECTIVTY 30°FROM LIGHT AXIS 5m(MIN) 7m(NOR) OK
_________________
HI

[RC]

EUROFIX, едно допълнение.
Ако наистина въпроса е за това шаси, то бутона Service го има в оригиналния пулт но не е изведен.

[LIM]

драстите ..
начи моито ТВ е НЕО 21 инчово .. менюто му е същото като описаното но в него няма за хоризонталната развивка настроика .. има само за позицията
как на тоя ТВ пък и на доста други (щот прегледах 4-5 и те нямат за свиване на Н) се свива странично картината ??? за вертикално има и за вертикално изместване има .. а за хоризонтално има само за изместване без за свиване

плс на [email protected] ако в възможно .. 10х предварително

[LIM]

сори за спама ма не намерих едит бутон

значи ТВ-то е 2121ТХ .. забраих да спомена

[dima]

Много малко от 21" телевизори имат регулиране на хоризонталния размер,досега в практиката съм срещал и чел за 2-3 модела.Има и няколко случая на корекция на хоризонтален размер и по хардуерен начин/последен случай на Филипс шаси L01.2/,за НЕО не знам но прегледайте за захранващото напрежение.Извинявам се за общите приказки,но в написаното от Вас няма никакви конкретни измервания и стойности.
_________________
Димитър

[mitachi]

Дима, да не говорим че може и да не си срещал регулиране на хоризонталния размер и на 14". Да, ама аз видях. И тъй като се наложи да сменя кинескопа, няма да коментирам фирми и марки, беше сложен оргинално втора употреба кинескоп на чисто нов телевизор, и като гледах отклонителната система, май производство от преди 25г.
Та затова в новите 14" телевизори вече си има всичко за регулиране. Знаеш ли от къде завода е попаднал на кинескоп? Шасито трябва да е пригодено за всичко! Жалко, че се налага да пиша това.
_________________
Не обръщайте голямо внимание, на това което съм писал след 22.00ч.

[Гост]

Мисля, че завода от поста на Mitachi е някъде в България, и то в Южна България. Ако кинескопа е бил trinitron, то фирмата и марката са ясни, макар, че там 25 години са много малко за ОС. Всъщност фирмата, с малки изключения, е ясна, независимо от кинескопа.

[pamporov]